LIMITED WARRANTY, DISCLAIMER, AND WAIVER OF CLAIMS

Thank you for purchasing a MOLD IN GRAPHIC SYSTEMS® Graphic Product (herein after referred to as the “Product”). We are pleased to present you with this Limited Warranty, Disclaimer, and Waiver of Claims (“Limited Warranty”).

The terms of this Limited Warranty state the entire obligation of Joram Corporation, dba MOLD IN GRAPHIC SYSTEMS® (herein after referred to as “MOLD IN GRAPHIC SYSTEMS®”), or its successor and assigns with respect to the Product. The Product is warranted only against any manufactured defects as described below within twelve (12) months from the date of manufacture and prior to application to a mold or any substrate. The remedies under this Limited Warranty against manufactured defects are strictly limited to replacement of the Product.

For the purposes of this Limited Warranty being provided to you (referred to herein as “Buyer”), the Product is supplied as a raw material component which is applied to a rotational mold or a polyolefin product by Buyer. MOLD IN GRAPHIC SYSTEMS® provides a full warranty that the Product meets technical specifications as tested and qualified by Buyer at the time of delivery. As MOLD IN GRAPHIC SYSTEMS® has no control over subsequent usage of molding equipment, graphics, or application parameters including such variables as graphic transfer pressures, rotational mold/polyolefin product conditions, and cure cycle times & temperatures that can have significant impact on the finished product, MOLD IN GRAPHIC SYSTEMS® does not provide and expressly disclaims any warranty obligation pertaining to the durability of the Product for any period. Once the Product is transferred or applied to any mold or substrate, MOLD IN GRAPHIC SYSTEMS® makes no warranty of any kind.

Should the Product fail to meet the technical specifications within 12 months of the manufacture date and prior to application, MOLD IN GRAPHIC SYSTEMS® will immediately replace, at its expense, the non-complying Product, provided that the Product had been stored in accordance with the following MOLD IN GRAPHIC SYSTEMS® climate controlled environment storage requirements:

  1. The Product should not be pressed or stacked upon.
  2. The Product should be stored at a temperature between 10c – 35c (50F – 95F).
  3. The Product should not be stored in direct sunlight.
  4. Partially used Product needs to be placed in a protective storage container.

In the event these requirements are not followed, this Limited Warranty is void. To prove that the Product does not comply with the technical specifications, Buyer must, in writing within 12 months of the delivery date and prior to application, provide MOLD IN GRAPHIC SYSTEMS® the Item Code, Item Description, PO Number and ID Number affixed to packaged Product bundles delivered to Buyer, and prove that the storage requirements have been met.

The Product is made from polyolefin materials. Successful application of the Product requires that three application components (e.g. graphic transfer pressures, rotational mold/polyolefin product conditions, and cure cycle times & temperatures) be in compliance with MOLD IN GRAPHIC SYSTEMS® technical specifications for proper application that results in complete fusion of graphic to substrate. Buyer understands that these settings impact Product performance. Upon request, MOLD IN GRAPHIC SYSTEMS® will provide free phone and/or email technical assistance to Buyer on the proper application of the Product. On-site assistance is also available at a mutually agreeable fee to Buyer. Once the application process has been initiated by Buyer, MOLD IN GRAPHIC SYSTEMS® no longer has control over the conditions to which the Product will be exposed and used under (e.g. application guidelines, operator error, temperature, environment, substrate, chemicals, etc.). As a consequence, MOLD IN GRAPHIC SYSTEMS® offers no warranty and cannot be held liable for the Product once the application process has commenced.

THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, PROVIDED WITH THIS PRODUCT. THE PRODUCT PROVIDED BY MOLD IN GRAPHIC SYSTEMS® IS NOT WARRANTED AS SUITABLE FOR ANY PARTICULAR PURPOSE PARTICULAR TO THE BUYER’S USES AND APPLICATION. IT IS THE BUYER’S RESPONSIBILITY TO DETERMINE, IN THE BUYER’S SOLE JUDGMENT, THE SUITABILITY OF THE PRODUCT FOR ANY PURPOSE PARTICULAR TO THE BUYER. MOLD IN GRAPHIC SYSTEMS® ASSUMES NO RESPONSIBILITY FOR THE SELECTION OR FURNISHING OF PRODUCTS SUITABLE TO THE INDIVIDUAL NEEDS OF THE BUYER. MOLD IN GRAPHIC SYSTEMS® MAKES NO WARRANTY OF MERCHANTABILITY OR OF THE FITNESS OF THE PRODUCT FOR ANY PURPOSE. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE FACE HEREOF. THE BUYER ASSUMES ALL RISKS OF PERSONAL INJURY OR PROPERTY DAMAGE FOR THE USE OF THIS PRODUCT.

MOLD IN GRAPHIC SYSTEMS® expressly disclaims any liability of any kind whatsoever, whether for negligence, product liability, strict liability or otherwise. Any damages for any tort, contract, breach of any expressed or implied warranty or any other type of claim that by operation of law survives this Limited Warranty are expressly limited to replacement of the Product. Buyer agrees that MOLD IN GRAPHIC SYSTEMS®, including its officers, directors, agents or employees, shall not be liable in any way for any damages of any kind, whether direct, indirect, punitive, special incidental or consequential damages, arising out of or relating to the use of this Product and/or for any kind of alleged defect in this Product, whether based in contract, tort, strict liability or otherwise.

BY PURCHASING THIS PRODUCT, BUYER EXPRESSLY WAIVES ANY AND ALL CLAIMS OR POTENTIAL CLAIMS WHICH MAY ARISE AGAINST MOLD IN GRAPHIC SYSTEMS®, INCLUDING ANY OF ITS OFFICERS, DIRECTORS, AGENTS OR EMPLOYEES, ARISING OUT OF OR RELATING IN ANY WAY TO BUYER’S USE OF THIS PRODUCT, INCLUDING ANY AND ALL POTENTIAL CLAIMS FOR NEGLIGENCE, STRICT LIABILITY, MISREPRESENTATION AND BREACH OF AN EXPRESSED OR IMPLIED WARRANTY OF ANY KIND AND BUYER EXPRESSLY RELEASES MOLD IN GRAPHIC SYSTEMS® AND ALL OF ITS OFFICERS, DIRECTORS, AGENTS OR EMPLOYEES FROM ANY SUCH CLAIMS.

If any part of this Limited Warranty shall be invalid or unenforceable, then the remaining provisions of this document shall remain in full force and effect. This Limited Warranty is governed by the laws of the State of Arizona and any other applicable federal law. By using this Product, you consent to bring any and all disputes arising out of or relating to the use of this Product in Arizona state court in Yavapai County, Arizona or in a federal court of competent jurisdiction in Arizona. By using the Product, you demonstrate your acceptance without modification of the terms, conditions and notices contained in this Limited Warranty.